DetonationEMS 1.3 Speeduino Standalone ECU Kit - Case Bluetooth Breakout & More

Description

DetonationEMS
Stand Alone Engine Management Systems
Budget Minded Engine Management without Compromise!
Included:
Hammond Extruded Aluminum Case with Custom 3d Printed End Caps
DetonationEMS v1.3 Board
Arduino 2560 with latest Speeduino firmware installed
2.5Bar Map Sensor (installed)
USB Cable for tuning.
IDC40 Breakout with Ribbon Cable
Bluetooth Module for wireless tuning
DRV8825 stepper module installed
Pin compatible to be a Speeduino v0.4x replacement the 1.3 takes everything great amazing about the 0.4x and improves ease of use and installation. Preconfigured direct relay control for cooling fans, fuel pump and a ready to use tachometer output. Then we added 4 more fully customizable medium current outputs and 2 more fully customizable analog inputs on a separate IDC8 giving you even more options including but not limited to fuel and/or oil sensors able to be configured for engine protection!
The Speeduino Project is an engine management project aims to create a flexible, fully featured Engine Management Systems (EMS aka ECU) based on the low cost and open source Arduino platform. DetonationEMS 1.3 as well as Speeduino v0.4x use the Arduino Mega 2560 R3 as the controller or CPU. (Arduino included with latest firmware pre-installed)
Hardware feature List:
4 injector channels
4 Ignition outputs
Fully protected input channels for CLT, IAT, TPS and O2
Optional VR conditioner mount on crank and cam inputs
MAP sensor mount location. (2.5-bar Included and installed)
DRV8825 stepper module mount location.
8 Medium-current spare outputs (e.g., Fuel Pump, Fan, Boost Control, VVT, etc..)
2 Analog Customizable Inputs (oil, fuel pressure or any 0-5v sensor)
Flex Fuel Maps for Fuel and Timing (ethanol content sensor required)
Bluetooth Header for HC-05/HC-06 Bluetooth Module (See Speeduino Wiki for setup instructions)
Firmware Feature List:
Supports up to 8 cylinders fuel and ignition with 4 channels of fuel and 4 channels of ignition outputs, 2 (Even fire only), 3 and 4 cylinder engines with full sequential fuel and ignition. 6 (even fire only) and 8 cylinder engines are supported with wasted spark and 2 squirts per cycle
16x16 3D fuel and ignition maps, with base of either TPS (Alpha-N) or MAP (Speed Density)
6x6 3D individual cylinder trim on engines up to 4 cylinders
After Start Enrichment
Rev limiting (Spark based, hard and soft)
Cranking specific enrichment, dwell timing and advance
General logging through TunerStudio
High speed tooth logging
TPS calibration through TunerStudio
Sensor calibration through TunerStudio (Coolant, IAT and O2)
Warm Up Enrichment (WUE)
TPS based acceleration enrichment
Tacho output
Fuel pump activation/deactivation (With priming)
Over dwell and over duty protection
Battery voltage compensation for dwell and injectors
Launch control
Flex fuel
O2 based autotune (Registered version of TunerStudio required)
Open and closed loop idle control (PWM and Stepper)
Closed loop boost control
Open loop VVT control
Deceleration fuel cut off (DFCO)
Overall Engine Protection system
Fuel and oil pressure (requires the use of additional inputs, see wiki)
Generic programmable outputs (requires the use of additional inputs, see wiki)
Water and methanol injection (requires the use of additional inputs, see wiki)
Vehicle Speed in MPH & KPH Logging and Display
Modular wheel decoder support. Included decoders:
Missing tooth (Eg 12-1, 36-1, 60-2 etc)
Dual wheel (Evenly spaced teeth on crank, single tooth on cam)
Basic distributor
GM 7X
GM 24X
4g63 aka 4/2
'Jeep 2000'
Audi 135
Miata 99-05
Honda D17 (12+1)
Nissan 360
Subaru 6/7
420a decoder
Each Unit is fully tested before shipping!
All Software, Firmware, Base-maps, Manuals and additional information links can be found on the Speeduino Wiki page.
Contact us:
We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We encourage our customers to contact us with any questions or concerns! We'd like to be sure you are completely satisfied with your purchase.
E.P.A. Federal Regulations, California (CARB), other states and governing authorities prohibit sale or use of some aftermarket parts, including those that tamper with, modify or defeat emission systems in any vehicle 1966 and newer.
DetonationEMS prohibits the use of it's products on emission controlled vehicles. All parts are sold for OFF-ROAD, RACE-ONLY, GROUND-VEHICLE USE PROPOSES ONLY.
© DetonationEMS.com